Edge banding adhesive – edge banding hot-melt adhesive suitable for bonding PVC, Veneer, ABS, and melamine resin edges.

Sofa assembly adhesive – Water-based, Hot Melt & Solvent-based adhesives suitable for foam assembly and lamination process.

Wood lamination adhesive – Select a grade for board, scantling or profile lamination. Any D4 classification requires product-specific documentation.

Finger-joint adhesive – polyvinyl acetate adhesive for finger joint application.

PVAc for wood jointing, dowelling and veneer lamination – Confirm the grade for cold, hot or high-frequency pressing. Verify any D3 classification and service conditions in its documentation.

Paper overlay adhesive – water based adhesive that specifically designed for paper overlay application. Commonly used on plywood, chipboard, MDF boards and HPL boards

Membrane press adhesive – water base adhesive with high molecular weight polyurethane dispersion. This product used as a heat activated. thermosetting membrane press adhesive.

Door assembly adhesive – Water-based and Hot-melt PUR adhesive suitable for door manufacturing process. Wood door lamination, honeycomb assembly and dowel joints.

Drawer Railing Adhesive – Water based adhesive suitable for assembling drawer railing in wooden cabinets.

Post forming adhesive – polyvinyl acetate for post forming process. Suitable for continuous through-feed post forming machines, manual bending machines and stationary post forming machines working in cycles

Veneer Splicing Adhesives- Hot melt adhesices in the process of tapeless splicing veneers on a wide variety of machines.

Tongue & Grooves Adhesive – Water based adhesive suitable for tongues & groove assembly.

Adhesives for woodworking and furniture production

Techbond Việt Nam supplies water-based, hot melt and two-component adhesive systems for wood jointing, edge banding, surface lamination and assembly. Select a grade for the wood or panel, facing material, equipment and service conditions. Adhesive families are not interchangeable.

Read the adhesive selection and production-trial guide

Water-based adhesives for wood jointing

PVAc white glue is one family of water-based adhesives used for panel jointing, finger jointing and furniture assembly. Not all water-based adhesives are PVAc. Suitability for cold, hot or high-frequency pressing must be confirmed for the specific grade and process.

Check the grade’s documented moisture-resistance classification. D3/D4 labels alone do not establish heat resistance, solvent resistance or suitability for load-bearing structures. Results also depend on the wood species, particularly oily woods.

Veneer lamination for furniture production

Techbond’s woodworking adhesive range includes PVAc adhesives for laminating veneer onto panels. This differs from joining the edges of thin veneer sheets, where hot-melt adhesives are used on suitable splicing equipment. For grade selection, provide the veneer and substrate types, bonding area, press type and moisture-resistance requirements so the relevant TDS and trial conditions can be reviewed.

Hot melts for edge banding and surface lamination

EVA, PO and PUR grades are selected for the application and machine. For PVC, ABS, melamine or veneer edging, check the backing treatment, line speed, application temperature and bond-line requirements.

Heat, moisture and solvent resistance and cleaning procedures depend on the grade. Do not apply an EVA operating procedure to PUR without checking the instructions. Machine splicing of veneer edges is different from laminating veneer onto a panel.

Two-component adhesives: identify the chemistry

“AB” describes two components; it does not identify an adhesive as epoxy. EPI wood-jointing systems and two-component epoxies have different chemistry, hardeners and operating conditions. Confirm the exact product before selection.

Follow the TDS mixing ratio, pot life and conditioning time. Do not substitute hardeners or transfer test results between systems. An adhesive joint does not automatically replace mechanical fixings in a design.

Select by production process

Panel and timber lamination

Discuss a suitable water-based or two-component system. Record wood species, moisture, joint fit and pressing method. Use a D4 designation only when supported by the specific grade’s documentation; assess heat exposure and outdoor service separately.

Finger jointing

Select PVAc or another system specified for finger jointing according to the wood, finger geometry, adhesive spread, assembly time and press cycle. Confirm the intended use and acceptance criteria before trials.

Edge banding and surface lamination

Select EVA, PO or PUR compatible with the machine and materials. Fire performance of doors or components requires assessment of the complete assembly; the adhesive name alone does not establish a fire rating.

Furniture assembly

Select water-based or two-component adhesives according to the material pair, joint gap, working time and service conditions. Evaluate bonds after the specified conditioning period, rather than only at press release.

Prepare a trial and quotation enquiry

Provide the wood/panel type, moisture, facing material and photographs of surfaces or joints.
Describe the application, equipment, line speed, pressing method, production volume and service environment.
Agree trial criteria for adhesion, bond-line appearance, edge lifting and relevant moisture/heat exposure.
Request the proposed grade’s TDS/SDS and confirm mixing ratio, open time, pressing, conditioning and pot life where applicable.
Ask about sample availability, packaging, order quantity and delivery destination when requesting a quotation. These conditions require product-specific confirmation.

Compare adhesive consumed per acceptable finished item alongside machine time, cleaning and rework, rather than price per kilogram alone.

Reference adhesive grades from the Techbond catalogue

Product grade	Application	Catalogue information
TECHBOND FJ 360; FJ 2006; FJ 392NS	Finger jointing	Water-based grades listed specifically for finger-joint applications.
TECHBOND L 13001; L 315	Wood lamination – D3 group	Listed under D3 Lamination; confirm classification and operating conditions in the grade-specific TDS.
TECHBOND L 14098; L 15115	Wood lamination – D4 group	Catalogue suitability: L 14098 for soft–medium density wood; L 15115 for medium–hard density wood.
TECHBOND HM 18080; HM 19575	Edge banding	HM 18080 for veneer edging; HM 19575 for PVC edging.
TECHBOND HM 11-3001	Veneer splicing	Unfilled hotmelt for joining veneer sheets, distinct from laminating veneer onto panels.
TECHBOND HMPUR 11-5008; 11-5009	PUR edge banding	Listed as polyurethane hotmelt grades for edge banding.
TECHBOND Epoxy A 38 + Epoxy B 38	Epoxy wood assembly	A two-component epoxy system, distinct from EPI.

Source: TECHBOND Product Catalogue, 2026 document supplied by Techbond, printed pages 8–9. This selected list supports initial discussions and does not replace grade-specific TDS/SDS or certificates. The catalogue does not establish each grade’s manufacturing origin or current availability in Vietnam; confirm these when requesting a quotation.

WOODWORKING ADHESIVES